Please check the variant selected prior to placing an order
Parameters:
- Diagonal wheelbase: 550mm
- Landing gear height: 260mm
- Weight: 630 ±2 g
- Material of the main board : 3k full carbon fiber
- thickness of the main board : 1.5mm
Recommended configuration:
- Motor: 3508
- Prop: 12-15 inch CW CCW
- ESC: 30A(2-6s) ; 40A (2-4S)
- Flight control: APM opensource flight control
- Battery: 4-6S Lipo
Pixhawk PX4 Autopilot PIX 2.4.8 32 Bit Flight Controller
Features:
1. The advanced 32-bit ARM CortexM4 high-performance processors, can run NuttX RTOS real-time operating system;
2. 14 PWM / servo output;
3. Bus interface (UART, I2C, SPI, CAN);
4. The integrated backup power and backup controller fails, the primary controller fails over to the backup control is safe;
5. Provide automatic and manual modes;
6. Provide redundant power input and failover;
7. Multicolor LED lights;
8. Provide multi-tone buzzer Interface
9. Micro SD recording flight data;
Specifications:
Microprocessor
1.32 2 MB flash STM32F427 Cortex M4, with hardware floating-point processing unit
2. frequency: 168MHZ, 256K RAM
3.32 STM32F103 backup coprocessor
Sensor
1.L3GD20 3-axis digital gyroscope 16
2.LSM303D 3-axis accelerometer 14 / Magnetometer
3.MPU6000 6-axis accelerometer / magnetometer
4.MS5611 precision barometer
Interface
1 .5 high voltage compatible UART 1, 2 with hardware flow control
2. 2 CAN
3.Spektrum DSM / DSM2 / DSM-X satellite receiver compatible input
4.Futaba SBUS compatible inputs and outputs
5.PPM Signal Input
6.RSSI (PWM or voltage) Input
7.I2C
8.SPI
9.3.3 and 6.6VADC input
10. External MICRO USB Interface
5010 360kv /750kv Motor :
These are really great outrunners. We've tested this line and they work extremely well. This is 5010-14 360KV /750kv Brushless Motor
Features:
1.Machined aluminum front housing with four fan-style cooling holes that pump air through the motor while it runs.
2.Rear threaded mounting holes with both 16 mm and 19mm hole spacings fit a variety of applications.
3.Specially designed NdFeB magnets with high temperature rating for trouble-free operation.
4.High Temperature 140 C (356 F) rated wire is used for winding the motors to minimize the risk of burning up the motor.
5.High quality stator plates are epoxy coated on the inner surface to prevent winding shorts. 0.20mm stator plate id used on this motor 5010.
6.High quality shielded and permanently lubricated ball bearings are used to support the motor shaft in all our motors.
7.High temperature adhesives are used to secure the stator windings and prevent them from shifting and getting pinched or shorting out .
Specifications:
Motor size: 50*10mm
Shaft size: 4mm
Weight: 80g
KV(rpm/v): 360/750
Battery: 2-6Li-Po
ESC: 20-40A
Best working with props of 14-16"
Package Included
- ZD550 Carbon Fiber Quadcopter frame kits x 1
- Carbon fiber Landing gear x 1 ( red color and green color landing protection foam send at random）
- 5010 750KV motor x 4
- ReadytoSky 40A OPTO 2-6S Brushless ESC x 4
- Pixhawk 2.4.8 32bit ARM Flight Controllerx 1 ( 2 kinds design of board sent at random)
- shock absorber x 1
- Safety button and buzzer x 1 ( 2 kinds of design send at random)
- 4G TF card (IO firmware has written) x1
- Neo-M8N Gps Module x1
- Black Gps Holder x1
- Power Module x1
- Pixhawk OSD OLED Display x1
- I2C Splitter Expand Module x1
- PPM Module w/ shell x1
- 433/915 MHZ telemetry with OTG Cable x1 ( send by your choice)
- 6pin turn 6pin cable x 1
- 4pin turn 4pin cable x 1
- 3pin DuPont line x1
- 5v/12v PDB x1
- battery belt x 1
- 1245 propeller x 4 pair